GMC Complaints
View complaints related to GMC. The complaints found here are submitted by actual consumers with first hand experience. You can submit your own complaint to the NHTSA or call the Hotline, Monday-Friday 8am to 8pm at (888) 327-4236, TTY: (800) 424-9153.
-
2015 GMC YUKON- Humble, TX
Electric Power Steering (EPS) assist was lost while I was driving the vehicle. As a result, I had difficulty steering the vehicle without power steering and almost caused a crash.
Source: NHTSA WEB SITE -
2020 GMC ACADIA- Virginia Beach, VA
1. Shift to Park failure, P0700/P187e internal sensor, causing me to have to get a rebuilt transmission. 10/2025 2. Transmission shudder/hard-shifting ongoing 2022-2025 3. Coolant/thermostat issues. Steering Assist Reduced" message, fans stay on HIGH, no AC, engine temp on ZERO ongoing since 2024 3. Start/Stop button failure multiple times (replaced 3 times) 4. Rack and pinion/steering gear (would not return/ got stuck while turning) got new rack and pinion 2023 5. Water pump leaking, replaced 4/2024 6. Since 2023, have had ongoing “Timing OVER ADVANCED”, warning issues since 2023. This is TOO MUCH for a New car!!! I’ve owned MANY cars and NEVER had this many issues!!! There appears to be multiple design flaws with this model and similar models!
Source: NHTSA WEB SITE -
2022 GMC SIERRA 1500- Omaha, NE
The contact owns a 2022 GMC Sierra 1500. The contact stated that while driving at various speeds, the tailgate opened unintendedly. The contact stated that the failure occurred while the vehicle was idling or while parked. The vehicle was taken to the dealer, where it was diagnosed, and the contact was informed that the failure was caused by a corroded wire. The dealer determined that the wire and the tailgate switch needed to be replaced. The dealer confirmed that the vehicle was not included in a recall or covered under warranty. The vehicle was not repaired but was scheduled for repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 65,000. The VIN was not available.
Source: HOTLINE VEHICLE OWNERS QUESTIONNAIRE -
2019 GMC ACADIA- Blue Springs, MO
I'm going to have to replace my thermostat and most likely my sensor. It will pop up saying (steering assist is reduced drive with care) my temperature gage on my dash will sometimes will not go up, my heat is acting funny. I've had also when I put it in park saying it's not actually shifted into park.
Source: NHTSA WEB SITE -
2021 GMC ACADIA- Broken Arrow, OK
For the 3rd time of ownership the cooling fan stays on after vehicle is turned off and the display “steering assist is reduced, drive with caution”.
Source: NHTSA WEB SITE -
-
2019 GMC ACADIA- Stow, OH
Thermostat stuck open and a steering assist light came on engine temp needle at zero. Check engine light came on, Had to have thermostat and coolant engine temp sensor replaced
Source: NHTSA WEB SITE -
2020 GMC SIERRA 2500- Gainesville, GA
The rear defroster massively overheated. It started heavily smoking and eventually exploded the rear windows. Only warning sign was the smoke which we noticed quickly because the windows were up. Had the windows been down we might not have noticed before a fire started. I'm taking it to a dealership now. This module also triggers on from a remote start. Extremely dangerous!!!
Source: NHTSA WEB SITE -
2021 GMC YUKON- Corpus Christi, TX
I got 3 messages on the dash going off simultaneously 1. Service Traction Control System 2. Forward Collision System unavailable 3. Service ESC I could feel the truck bogging and shaking a little at this point Then soon after the check engine light was flashing and it was noticeably misfiring and rough idling. I pulled some codes at Oreillys and got back 1. P0300 misfire 2. P050D cold start rough idle
Source: NHTSA WEB SITE -
2022 GMC ACADIA- Heber Springs, AR
The “Steering assist reduced” message came on and, when shut off, the fan blows very hard and loud.
Source: NHTSA WEB SITE -
2017 GMC ACADIA- Northwood, OH
While driving get notice lane departure not working and thermostat registered zero, when code scanned, states low thermostat temp and able to reset with code reader. Will reoccur in minters to days later. This is an electrical issue to to the ability to reset with a code scan tool, but also a safety issue since it also effects the electrical safety ability associated with the sensor.
Source: NHTSA WEB SITE