2008 JEEP WRANGLER Complaints

"On March 4, 2022, Customer Satisfaction Notification S33 (Airbag Clockspring Recall Remedy) was performed on my 2008 Jeep Wrangler by an authorized dealer at 123,314 miles. The vehicle now has 137, 347 miles. The replacement clockspring provided as the official safety remedy has completely failed after only roughly 15,000 miles of driving, illuminating the SRS airbag warning light and completely disabling the supplemental restraint system. The manufacturer's mandated remedy has failed to permanently correct the safety defect, creating a recurring hazard." Tom O'Brian dealership and Stellanis have both refused to repair clockspring which is either defective repair item. "Stellantis corporate directed me to speak with you directly regarding a safety component failure. Tom O’Brien Jeep performed the S33 clockspring campaign on my Wrangler at 123,314 miles. The vehicle only has about 138,000 miles on it now. This critical airbag safety component failed after just 15,000 miles of driving. Corporate told me that if you submit a Digital Goodwill Claim through the dealer portal for an internal part failure on a safety campaign, they can review it for approval. Because this disables my entire airbag system after only 15,000 miles, I am asking you to submit that goodwill request so Stellantis can cover the replacement." ," no federal safety regulator or corporate executive expects a vital component of a vehicle's supplemental restraint/airbag system to fail after just 15,000 miles. This extremely low mileage proves one of two things: either the replacement remedy part was defective out of the box, or the "dust shroud" modification required by the S33 campaign was not installed correctly, allowing the new clockspring to fail prematurely.

ABS systems not functioning properly, showing engine code U0121 that states lost communication with ABS module. This is a common occurrence with jeeps and is a safety issue due to the abs system not working properly. Also causes the brakes to randomly engage and disengage.

While driving at speed, vehicle electrical went haywire. Headlights went on and off. Horn sounding on and off, Wipers and washers going on and off, HVAC blower on and off. Pulled over vehicle and turned off and removed key and it still remained running, all horn, lights, and wipers still going on and off. Opened hood, removed negative battery terminal, and with that, car still ran! Was several minutes and car finally shut itself off. Scary that the car went completely haywire and would not shut off, even with key out, and battery disconnected!

The ABS computer brake module is bad in my jeep. It needs a replacement. Confirmed by Chrysler Jeep dealership. However, Chrysler does not offer a replacement module. ABS does not work on my vehicle. This is a huge safety issue and is common problem among this year Jeep. Chrysler shouldn’t be allowed to NOT have a replacement OEM ABS module. Huge safety risk and lawsuit

I was driving down the road in my 2008 wrangler and all of the sudden every light flashed on my dash board then it felt like I could not shift gears then smoke came pouring out of my air vents. I pulled over and got out realizing it was on fire. Climbed in to save my dog just before the fire got huge. My entire Jeep is gone.

April 22, 2025 my 2008 Jeep lost power. There was a sequence, where one warning light was followed by another, followed by a complete loss of power. I charged the battery, car started up, I drove to dealer (a 5-minute trip), and by my arrival the Jeep had again lost all power. Dealer checked the vehicle, and told me the battery and charging system were fine, but the ABS brake modulator was draining the power. They have not been able to get another modulator and the vehicle is still at the dealer (Crown Chrysler Jeep Dodge Ram Dublin, OH). Losing power precipitously presents a safety hazard.

The vehicle requires an ABS module. I have been waiting for over 4 months for part availability. According to dealer they dont have any ETA on availability and have been told it may not be something they ever go back to producing. My state requires safety inspection which it will not pass due to this issue. Seems to me that someone needs to be responsible to make a part for these issues.

This is a common flaw with the abs brake system on many Chrysler Fiat vehicles and Chrysler fiat is doing NOtHING. My Jeep ABS computer module went bad . No damage, no off roading. Driving on highway and all the brake/abs/stability control lights lit up on my dash. The abs showed code “c2200” bad abs module and must replace. However Chrysler stopped making these …in back order for years. You have to either get a junk yard part or send your computer away to be Refurbished. How can Chrysler be allowed to not have a critical safety part in stock…and not cover this in a lifetime warranty. ?? I’ve never had any other vehicle where the abs computer goes bad . This is insane. And dealer can’t locate the part in the USA because Chrysler doesn’t have them.

ABS Module Yes As I was driving and going to turn left into a shopping center and stepped on the break, I had none, I did almost crash. It happened all of a sudden out of nowhere no lights, no icons lit. The problem has been confirmed by a dealer stating that this is a nationwide issue that’s currently going on that the parts are back ordered because there is nothing in production right now for the part. The vehicle is not drivable.

Defective Wheel Spacers Causing Vehicle Failure and Safety Hazard While driving, the front driver-side wheel spacer failed, leading to the complete detachment of the wheel from my vehicle. This unexpected and catastrophic failure left us stranded on the highway for several hours, waiting for roadside assistance. Additionally, the front end of the Jeep sustained significant damage, requiring extensive repairs. Fortunately, we were able to bring the vehicle to a stop without injuries, but the situation could have resulted in a far more serious accident. Upon further inspection by road side assistance, it became evident that the wheel spacer had completely failed, raising concerns about the safety and reliability of this product. I immediately contacted Yitamotor to seek an explanation, reimbursement for damages, and information on whether this issue is a known defect in their product. In my formal request to the company, I outlined the following concerns: Investigation: I requested a thorough investigation into why the wheel spacer failed and whether similar failures have been reported. The supplier has no interest in investigating the failure. The part failed without warning. There are no direct sensors or indicators for this particular part. They claim the part is made of forged metal.