KENWORTH Complaints

2022 KENWORTH W900. CONSUMER STATED THAT WHILE DRIVING VEHICLE BEGAN TO VIBRATE AND STEERED TO THE LEFT ON ITS OWN. THE CONSUMER STATED THE VEHICLE CRASHED INTO A WALL BARRIER.

The contact owns a 2019 Kenworth T680. The contact stated while driving 75 MPH, there was an abnormal popping noise detected and the vehicle decelerated and the fuel system detached from the vehicle. The vehicle was towed to an independent mechanic and the contact was informed that the pump bolt had fractured. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified. The approximate failure mileage was 432,549.

While driving the factory floor mat can slide under the rear of the brake pedal while it is being applied. Once pedal is released it will still hold brake pressure causing brakes to remain engaged while still allowing vehicle to move down the road in turn causing brakes to heat up and either lockup/ catch fire or once cooled become inoperable. We have heat marks on exterior of front drums and pads were glazed over.

I am analyzing a rollover event with the subject Kenworth T270 configured as a tanker truck. The driver's safety belt was configured with an "IMMI Comfort Latch" shoulder belt tension reliever. It appears that this system is in violation of FMVSS 208 sections S7.4.2 and S7.4.5 due to the fact that there is no automatic release of the tension relieving device upon opening of the driver's door or release of the driver's buckle latch. In the subject accident, the inexperienced young driver, whoi had never driven a vehicle with a "Comfort Latch" safety belt tension relieving device, apparently just buckle the safety belt around him, unaware that the shoulder belt had excessive slack in it, due to a previous driver having set the "Comfort Latch". IN the rollover event he was ejected from the vehicle and was killed in the accident.

This Truck Was Park. The Paccar Engine MX13 and Chassis Harness from the Driver Side Shortaged, causing a Fire in the back of the engine and ABS Harness under the Steering Shaft. Plástic and Rubber wire insulation Melted with the fire causing it to drip on top of the water seperator cap which resulted in a fuel flame that caused even more damage throughought the outstanding components. This problem could've resulted in total loss of the unit.

The contact owns a 2014 Kenworth T660. The contact received a recall notification for NHTSA Campaign Number: 20V199000 (Electronic Stability Control, Service Brakes, Air). The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue. The part was not available for repair. The contact had not experienced a failure. Parts distribution disconnect.

The vehicle drifts to the right and will not track in its lane. In addition there is a hard pull to the right upon hard braking. There is also front end vibration. It has been taken to the factory authorized facility a number of times and has been in the shop for more than 3 months in the last approximate year.

Seat belt frame cover was cracked and seat belt would not retract. The other side was broken as well with casing coming off. I was in the middle of backing for a delivery and the driver seat retract would not stay in place and the seat kept folding forward causing me to not be able to back the truck. I was told this is due to obese drivers causing the seat to break. Also during the time of my brake issue where are the brakes locked up and on several other occasions the air brake lost pressure for no reason.

I started the truck after not driving for 1 day and a heavy rain storm the day prior. I attempted to drive bobtail when the brakes locked up. The traction control light came on then went back off. Then the adaptive cruise control notification came on. The regon came on then went back off. A speedometer sign with an exclamation mark came up and would not go away. After attempting to go down the road the brakes continued to lock up, would not release and caused the rear passenger tires to go bald and lose my job.

AUTOMATIC EMERGENCY BRAKING IS AN ABSOLUTE DANGER TO THE MOTORING PUBLIC AND NEEDS TO BE ELIMINATED IMMEDIATELY. I AM SICK AND TIRED OF ENGINEER'S WHO DON'T KNOW THEIR ASS FROM A HOLE IN THE GROUND DESIGNING BULLSHIT THAT DOESN'T WORK. FAR TOO MANY FALSE RADAR RETURNS AND UNWANTED HARD STOPS TO BE OF ANY USE. I DO NOT OWN THIS VEHICLE BUT IF I DID THE FIRST THING I WOULD DO RIGHT AFTER I PULL THE FUSE FOR THE LANE DEPARTURE WARNING WOULD BE TO ISOLATE AND BYPASS AEB. THIS WILL BE DONE ON ANY VEHICLES I PURCHASE IN THE FUTURE AND I DO NOT CARE WHAT THE LAW STATES ABOUT DOING SO