2010 MAZDA MAZDA6 Complaints

View complaints related to 2010 MAZDA MAZDA6. The complaints found here are submitted by actual consumers with first hand experience. There are more than 220 complaints submitted for the 2010 MAZDA MAZDA6. You can submit your own complaint to the NHTSA or call the Hotline, Monday-Friday 8am to 8pm at (888) 327-4236, TTY: (800) 424-9153.

  • 2010 MAZDA MAZDA6
    - Clermont, FL

    The dasboard on the rite side is melting, causing a sicky like surface and is reflecting the light on to the driver, making it hard to drive.

    Source: NHTSA WEB SITE
  • 2010 MAZDA MAZDA6
    - Toledo, OH

    The contact owns a 2010 Mazda Mazda6. The contact stated that the vehicle had previously been serviced at the dealer under NHTSA Campaign Number: 18V631000 (Suspension, Structure). The contact stated that while driving at an undisclosed speed, she lost control of the vehicle. The failure caused the passenger's side rear tire to rub on the fender while driving. The vehicle was taken to an independent mechanic who diagnosed that the passenger's side rear subframe was severely corroded and had fractured in half. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 82,000.

    Source: HOTLINE VEHICLE OWNERS QUESTIONNAIRE
  • 2010 MAZDA MAZDA6
    - Fruitport, MI

    Crossmember rust from recall campaign 2818I is able to effect structural attachment despite recall work. The recall installed an "improved: cross member. This was not an actually replacement cross member, rather additional plate steel between the rear and front of the existing attachment points of the defective OE cross member. Improved cross member contains no provisions to support rapidly corroding lower control arm attachment point in original cross member. Added member for recall also does not appear to additionally support lateral stresses from control arm. Evaluation of original cross-member seemed inadequate to detect structural integrity based on condition of the cross member today. "improved" cross member does not support mounting points of the control arm. Based on recall documents, some "improved" cross members have supports for Lower Control Arm (LCA) mounts. This issued occurred with sudden change in steering and braking characteristics. Vehicle suddenly started pulling right. Issue further exacerbated after follow on braking. Passenger wheel suddenly lost alignment and camber is indicating lower attachment geometry change. I was able to control vehicle, but with significant effort.

    Source: NHTSA WEB SITE
  • 2010 MAZDA MAZDA6
    - VONORE, TN

    The dashboard is sticky and shiny and the glare from the sun is terrible. It’s almost like the dashboard is “melting”

    Source: NHTSA WEB SITE
  • 2010 MAZDA MAZDA6
    - Harrison Township, MI

    My front sub frame was completely rotted, unsafe to drive and was repaired with Mazda's recall. It now appears that the REAR sub frame is rusting at an excessive rate. I have been reading several complaints where the same incidents are happening with the rear sub frame snapping while people are driving. Car is not safe. This needs to be addressed by Mazda. They are aware of front sub frame, but failed to include the REAR sub frame. Not sure what to do at this point, it will costs thousands to repair, yet is NOT SAFE to drive. Please look into this matter as this is a very serious issue and will result in serious injury or death.

    Source: NHTSA WEB SITE
  • 2010 MAZDA MAZDA6
    - Brunswick, OH

    I purchased this vehicle for my 16 yr old daughter 1 yr ago. The car has a clean carfax and has had no accidents. Upon purchasing the car the headlights continue to burn out. Taking it to a Mazda dealership i learned the headlight assembly unit was melting. I had to purchase 2 used headlight assembly because new from the dealership are 1,000 a piece. 2 used but perfectly working headlights were installed and within a yr the headlights had burned out again. I went to change the bulbs only to learn the headlight assembly were once again burnt. I have to purchase 2 new headlight assembly again but the mechanic can not guarantee that this burning situation won't occur. After calling around to places to find headlight assembly I have come to find out many are burnt. This seems like a real problem considering you need headlights to drive at night. Spending 1,000 everytime my headlights burn out seems 100% unreasonable and the fact that there is cleary a wiring issue within the headlight assembly unit itself seems to be a problem. I have been on multiple forums and this is a common issue. Please fix the problem!!!!!!

    Source: NHTSA WEB SITE
  • 2010 MAZDA MAZDA6
    - kent, OH

    after exiting the highway at 65+mph turned the corner and the rear of the car dropped and started dragging the ground without warning . pulled over to see rear suspension on the ground .i contacted dealer about it and they seem to be aware of similar complaints but do not seem to care .could have been different outcome one minute earlier !! this is the second time the frame collapsed on me in this car the first time was the recall 2818l same thing broke without warning . this is bad metal in the frames and someone is gonna die before mazda admits the cars are unsafe as lots of these cars are still on the road .

    Source: NHTSA WEB SITE
  • 2010 MAZDA MAZDA6
    - Ann Harbor, MI

    The contact owns a 2010 Mazda Mazda6. The contact stated that the steering wheel was pulling without warning. There was rust on the frame. The vehicle was taken to an independent mechanic and the contact was informed that the vehicle was not safe to drive. The local dealer was contacted. The vehicle was diagnosed and repaired. Mechanic noted that Mazda’s recall repair only served to keep the car from splitting apart, but it in no way resolved the control arm issue. As a result my car was unexpectedly swerving all over the road and was difficult to control. It was with the control arm still somewhat attached, though extremely loose. The contact stated that the vehicle was previously repaired under NHTSA Campaign number 18V631000 (Suspension, structure). The manufacturer was not contacted. The failure mileage was 151,000. Consumer stated there is significant rust on on side, where control arm attaches to steering. Vehicle has been repaired.

    Source: HOTLINE VEHICLE OWNERS QUESTIONNAIRE
  • 2010 MAZDA MAZDA6
    - Bay City, MI

    The wheels were turning in and the steering was really hard to keep straight had to turn the steering wheel almost half around car make Loud screaming noises.tires went flat ..i have 6 grandkids lucky I wasn't going fast the car could of flipped .subframe broke in half on passenger side rusted right out.i got this car from right way dealership in Saginaw Michigan in march of 2019 they never told me or never contacted me that there was a recall for the subframe breaking.could of killed someone!!!!

    Source: NHTSA WEB SITE
  • 2010 MAZDA MAZDA6
    - ERLANGER, KY

    PASSENGER SIDE DASHBOARD HAS MELTED, CAUSING BLACK STICKY RESIDUE AND A VERY SHINY EFFECT, WHEN TRYING TO DRIVE, THE SUNLIGHT AND NIGHTTIME LIGHTS CAUSE A GLARE THAT IS VERY DISTRACTING WHEN TRYING TO DRIVE.

    Source: NHTSA WEB SITE