2022 FORD F-250 SD Complaints

While driving between 65-75 mph the truck starts to vibrate in the rear. When I first bought it they said it was a heat shield but noice is getting worse and vibration is felt in floor. It has been to dealer twice now and on 4/24 will be the third time.

The drivers door power door lock fails to operate either to unlock the vehicle or to lock it. This is a safety risk as the power door lock should automatically lock the door once the vehicle reaches a certain speed to help doors remain shut in roll over accidents. Automatically locking the door also provides some security to occupants for carjacking. This problem first started when the door lock actuator failed to work in freezing weather at approximately 19,000 miles. The dealer was unwilling to repair it under warranty do to not being able to duplicate the condition despite video evidence. The problem has progressed to where it now no longer functions at all. This is not an uncommon issue as I have spoke with others who have had the same failure. Previous model year trucks have has customer gotten extended warranty from Ford to cover the lock malfunctions. Customer Satisfaction Program 20M04. Links to others reporting the same/similar issue: [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact's husband owns a 2022 Ford F-250. The contact stated while her husband was driving 30 MPH and pulling into the dealer's driveway for an oil change, the vehicle stalled. An unknown warning light was illuminated. The vehicle failed to restart and was pulled into the service bay. The dealer was able to diagnose the vehicle with the assistance of a manufacturer field technician. The dealer diagnosed that there were metal shavings in the oil and in the fuel system. The dealer repaired or replaced the internal high-pressure fuel pump components. The contact later received notification of NHTSA Campaign Number: 24V957000 (Fuel System, Diesel); however, the part to do the recall repair was not yet available. The contact stated while the dealer was performing an oil change on the vehicle recently, and the dealer informed the contact that there were metal shavings in the oil and there was oil leaking into the engine compartment. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and informed the contact they could not verify the recall remedy status information. The failure mileage was approximately 50,000. VIN tool confirms parts not available.

The contact owns a 2022 Ford F-250. The contact received notification of NHTSA Campaign Number: 24V957000 (FUEL SYSTEM, DIESEL); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue. The manufacturer was not made aware of the issue. The contact's husband stated that while driving 70 MPH, the accelerator pedal was depressed, and the vehicle failed to respond. The check engine warning light was illuminated. The contact's husband stated that the check engine warning light was illuminated, and the vehicle lost motive power. The contact stated that after turning off and restarting the vehicle, the vehicle functioned as needed for several days. The vehicle was then taken to a dealer and the contact's husband was informed that there was no technician available to repair the vehicle. The vehicle was diagnosed with turbo failure. The vehicle was not repaired. The failure mileage was approximately 82,000. VIN tool confirms parts not available.

The contact owns a 2022 Ford F-250. The contact stated that while his son was driving at 3 MPH, the vehicle jerked abnormally. There were no warning lights illuminated. The contact stated that the vehicle should have been included in NHTSA Campaign Number: 22V087000 (Structure, Power Train). The vehicle was then taken to a dealer where it was diagnosed, and the contact was informed that the transmission output shaft shield and heat shield needed to be replaced. The vehicle was not yet repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 86,900.

The component of issue is the rear drivers side FOX shock added by Tuscany Motor Co, majority owned by Fox Factory. This component collides with the rear brake fluid line causing excessive wear. Eventual failure of this line could potentially cause brake failure leading to a major road hazard. This component is available for inspection upon request. According to my local dealership, other Shelby Super Bajas have the same design flaw with the shock absorber. This component/issue has not been inspected by the manufacturer, police, insurance, or others besides my dealership. There were no warning lamps or other forms of warning besides visual excessive wear of the brake line.

Injector learning offset limits keeps triggering a code. Fuel consumption goes way up. Ford just clears the code but it always comes back.

Injector offset learning limits keeps triggering a engine light. Fuel consumption goes way up. Ford doesnt fix the problem they just keep clearing the code, but it always comes back

Check engine light comes on with injector codes. Ford clears the code and the problem continues to come back. Truck uses a lot more fuel when this is active. No help from Ford on getting this resolved. Issue: Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) after various fuel system repairs. This may be due to incorrect learned values in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM, reprogram the transmission control module (TCM), and perform the Reset Minimum Fuel Mass Adaptions All Cylinders.

Check engine light comes on with injector codes. Ford clears the code and the problem continues to come back. Truck uses a lot more fuel when this is active. No help from Ford on getting this resolved. Issue: Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) after various fuel system repairs. This may be due to incorrect learned values in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM, reprogram the transmission control module (TCM), and perform the Reset Minimum Fuel Mass Adaptions All Cylinders.