2015 FORD MUSTANG Complaints

The contact owns a 2015 Ford Mustang. The contact stated while driving at various speeds and while the vehicle was parked, the windows went up and down, the doors unlocked, the back-over prevention camera engaged, the trunk opened, and the exterior lights engaged independently. Additionally, the check engine warning light was illuminated. The vehicle was taken to the dealer, where it was diagnosed that the harness that extended from the rear to the front of the vehicle had failed. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 22V082000 (Back Over Prevention) however, the failure persisted. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage approximately 85,000.

Back up camera goes in and out, fuel pump started making bad sounds a few month after buying it like screeching sounds got the car around 39000

The contact owns a 2015 Ford Mustang. The contact stated while driving 50 MPH, the vehicle began to vibrate violently. The contact stated that the failure was intermittent at first but had since occurred while driving 50 MPH or faster. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who diagnosed failures with the center support bearing and drive shaft assembly. The vehicle was not repaired. After investigating the failure, the contact related it to NHTSA Campaign Number: 17V408000 (Power Train) but the VIN was not included. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. The failure mileage was 99,000.

The contact owns a 2015 Ford Mustang. The contact stated while operating the vehicle, the back-over prevention camera displayed a distorted screen. The vehicle was taken to the local dealer and serviced under NHTSA Campaign Number: 22V082000 (Back Over Prevention). After retrieving the vehicle, the failure was still present. The contact stated that the back-over prevention camera display became inoperable and only a blank screen was displayed. The cause of the failure was not yet determined. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 96,000.

The contact owns a 2015 Ford Mustang. The vehicle was taken to the local dealer to be repaired under NHTSA Campaign Number: 22V082000 (Back Over Prevention). The vehicle was repaired. The contact stated that while reversing, the camera became inoperable. The image was not available, and the check with the dealer message was displayed. The vehicle was taken back to the local dealer but was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 73,000.

The fuel tanked cracked. It was no longer able to hold vacuum. The engine light came on and stayed on. The 2.3L mustang had a similar issue due to heat. It was inspected and fix at a local repair shop.

The welds on the top of the clutch pedal at the pivot point were insufficient from the factory and failed. I was having issues operating the clutch and after doing some research found that this is a common issue and was never covered under any factory warranty. I did not have this inspected at a dealer because I knew it would not be covered. I was able to remove the pedal assembly and repair it and added additional welds myself. I think this is a huge safety concern due to the possibility of the clutch pedal cracking completely and coming loose, which could cause the vehicle to unexpectedly engage the clutch and run someone over or cause a collision. I have photos of the damaged components. It took me a total of 8 hours to complete the repairs. I am also concerned about the quality of the steel used to construct the pedal as it may be too brittle. The OEM should re-design this part and update their manufacturing & welding proceedures.

The little rubber pad that it attached to the brake pedal disintegrated. Without that pad the vehicle goes into limp mode and won’t drive over 40. Don’t know why the brake switch is connected to other electronics in the vehicle that would make it go into limp mode. Very unsafe while driving on the highway.

The contact owns a 2015 Ford Mustang. The contact stated that he received the recall notification for NHTSA Campaign Number: 22V082000 (Back Over Prevention) four years ago. The contact stated that every time he scheduled the appointment to have the recall repair completed at the dealer, it was informed that the part was not available to complete the repair. The contact stated that while he was driving in reverse mode, he noticed the back-over prevention camera was inoperable. The vehicle was taken to the dealer, where the contact was informed again that the part was on backorder. The vehicle was not repaired. The contact stated that the dealer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the failure but confirmed that parts were not yet available. The manufacturer was not made aware of the failure. The failure mileage was approximately 1,000. Parts distribution disconnect

The contact owns a 2015 Ford Mustang. The contact stated that while driving at unknown speeds, the valve cover was engine oil leaking onto the exhaust manifold. There was smoke coming from underneath the hood. There were no warning lights illuminated. The vehicle was taken to an independent mechanic and four new head gasket holes were drilled, and bolts were added. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was 55,000.