2013 MAZDA MAZDA3 Complaints

The Brake Pedal consistently malfunctions, even after the replacement of the master cylinder (by independent service center). The master cylinder does not hold pressure due to a faulty ABS control unit (which, when Mazda was contacted, said that part was on backorder until September). If the manufacturer knows this is an issue and can't supply the part due to so many replacements needed in their vehicle, why is there no recall? There is no warning to the driver on the dashboard of this issue and has causes repeated issues while breaking.

There seems to be a lot of people who own 2012 and 2013 Mazda 3 Sedans (with SKYACTIV-G 2.0L and Halogen Type Headlights) that are dealing with the same issue I am dealing with myself. I have just purchased a used 2013 Mazda 3 with Skyactive Technology and I noticed that when I was braking the headlights would pulse on and off and would continue while I braked. I have been told there is a TSB on this issue (attached) and Mazda is well aware of this happening. This concern is caused by inadequate alternator output controlled by the PCM when the battery is under a heavy load. They are to the point now of charging people for a doing the TSB on the car that is causing the problem of the alternator not producing the proper wattage to support both the headlights and the brake lights at the same time. There are numerous online forum entries that speak of this issue with 2012 and 2013 Mazda 3's. I am very concerned that my headlights may stop working which could result in my death or the death of my occupants of my vehicle not to mention the other motorists on the road around me if my head lights were to eventually fail at night due to lack of proper wattage to the headlights. There are videos on you tube that show these pulsing headlights on Mazda's. I believe that headlights are important enough safety issue that their failing could result in death if the headlights completely failed due to the known fault in these vehicles over time.

Transmission Control Module malfunction. The AT light came on and the car made a jerking motion and a clunking noise. It lost power and would not shift which is very dangerous in moving traffic. It put me at risk for getting hit by another vehicle not expecting the abrupt change in speed by my vehicle. The check engine light is now lit up. There were no warning lights before the vehicle’s transmission malfunctioned. A code came up on the vehicle when tested. U0101 lost communication with TCM. From what I have read, researched, and have been told this issue is very common for certain years of Mazda 3’s including mine.

The contact owns a 2013 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 16V644000 (Structure) however, the part to do the recall repair was not yet available. The local dealer was contacted, and the contact was informed that the part for the recall repair was not yet available. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.

All my seatbuckels are tearing. I thought it could of been my dog, but I a certain I did not give up my seat or let him drive. My driver side is also tearing. I noticed the buckle catching when securing it, and now it has moved past snag and had a quarter inch tear that it catches on. The buckle is not wide enough for the belt. The belt is no longer able to constraint as good as when it was whole. Unknown

After filing up the gas tank, there is a strong smell of fuel coming from the car. It remains strong until the tank is run down to about 3/4. Gas can be seen dripping down the tank under the car. Gas drips are clearly visible on the ground. This has been an ongoing problem for approximately two years.

Steering becomes unpredictable and stiff accompanied by surging and loss of power. Check engine light comes on. Code P0882

ABS Module suddenly start failing causing brake sinks down. Almost crashed because of it. It appears to be a very common issue but Mazda still does not recall these ABS modules made by Ford/ATE. Also, it does not show any ABS warning light, which might be why not many people have called on this as they probably thought it was normal. There is all sort of communication error codes if you read with a OBDII scanner. In fact, Ford had a recall for these ABS modules, citing "stuck or slow-responding valves due to reaction with brake fluid".

I had the dashboard recalled and replaced. The new dashboard is separating from the computer screen on dash.

TRACKING NUMBER 11461728 ADDED INFORMATION EMAIL FROM MANUFACTURE MITSUBUSHI ELECTRIC INCORPORATED