2011 MAZDA MAZDA6 Complaints

The contact owns a 2011 Mazda Mazda6. The contact stated that while driving at an undisclosed speed and coming to a stop, the steering wheel was not operating properly. Several days later while the contact's wife was driving at an undisclosed speed, there was play in the steering wheel. Additionally, there was an abnormal sound coming from the passenger’s side wheel. The contact stated that the wheel was turning abnormally. A mechanic arrived at the residence to diagnose the vehicle and determined that the sub frame was rusted. While touching the sub frame, pieces of the sub frame fractured. The dealer was notified of the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 92,000.

The contact owns a 2011 Mazda Mazda6. The contact stated that while driving at 25 MPH, the contact attempted to swerve out the way of another vehicle as she suddenly lost control of the vehicle. Due to the failure, the contact force to steer the vehicle to the left as the contact attempted to maintain control of the vehicle. The contact managed to pull over into a parking lot and called her husband for assistance. Despite the failure, the contact managed to drive the vehicle home despite the vehicle being extremely difficult to maneuver. The contact's husband managed to drive the vehicle to a local mechanic, who determined that the front subframe had failed due to excessive corrosion of the subframe. The mechanic then informed the contact of NHTSA Campaign Number: 19V323000 (Structure, Suspension); however, the contact was informed that her vehicle was not included in the recall. The manufacturer was notified of the failure where they confirmed that the vehicle was not included in the recall. The vehicle remained in the mechanic's possession and had yet to be repaired. The failure mileage was 115,000.

Front Subframe has corroded and broke. There is a recall on the subframe that was repaired by dealership in 2019, but this repair did not fix the issue since it has now rusted through and broke. The repair was faulty.

Car developed a known recall issue problem, Recall 2818I. Even though Nebraska was not listed as a "salt state", it's obvious that Nebraska has similar conditions to Iowa. Attempts to contact Mazda USA corporate would not even fix the issue, citing cars age and other factors even though the damage is very specific to this particular recall.

2011 Mazda6 A serious safety defect occurred on my vehicle and matches NHTSA Recall 19V-323 / Mazda Recall 2818I (front cross member corrosion due to insufficient coating) despite this recall not being associated with my VIN. Front cross member cracked due to rust, causing loss of steering control, wheel misalignment, and scraping from the front wheel. This is exactly the failure described in the recall (breakage of the cross member and reduced steering control, increasing the risk of a crash). My safety and the safety of others were put at risk. Although my VIN is not currently associated with the recall, all conditions of the recall apply to my vehicle: -2011 Mazda6 within the affected production range -Defect is a manufacturing issue (insufficient paint coating) -Vehicle was registered in Missouri from 2023-2025, which is a listed state The only reason this recall was not associated with my VIN is because the vehicle was not registered in Missouri at the exact time of the 2019 recall campaign. This is an administrative gap, not a safety distinction. It should not be allowed to limit a manufacturer safety defect to specific states. Vehicles move across state lines constantly. A defect that causes loss of steering control does not stop being dangerous when a car crosses a border. Registration records alone did not reflect actual vehicle use or risk. If recalls are state-limited, manufacturers and NHTSA must continue tracking registration changes and associate the recall with the VIN as soon as a vehicle becomes registered in an affected state. Rust is progressive and age-related. Since this recall began in 2019 and it is now 2026, affected vehicles are more likely to experience failure, and many are now registered in different states than they were in 2019. I am requesting that NHTSA associate Recall 19V-323 with my VIN, investigate the adequacy of state-limited recall tracking, and take action to prevent this known safety defect from causing additional crashes.

When I took the car into my ASE mechanic shop for a normal oil change and tire rotation, they performed a general overall car inspection. They noticed that the Driver Side Rear Subframe had rusted through completely, where the coil spring is located. The passenger side was rusted, but has not yet broke through. They stated that the subframe parts should not rust through like this. They also stated that it is dangerous to drive the car in this condition. I have not notified the manufacturer as of yet, but plan to do so. There were no warning lights, but the ride did seem to be rougher than normal. The attach photos contain 2 photos of the failed driver side rear subframe and 1 photo of the good, passenger side rear subframe.

2011 Mazda6 rear subframe rot/rust, unsafe and dangerous to drive, Same situation as the front subframe that is part of a recall.

The front and back cross members underneath my Mazda6 have completely rusted out. There are numerous complaints about Mazda's "Safety Recall 2818I Expansion" not covering the back support member and also not considering Nebraska to be a Salt Belt state despite the state, and specifically Omaha using salt to treat their roads in the winter. On [XXX], my front cross member completely failed due to rust, causing my vehicle to lose control. I've taken my car to the mechanic and they confirmed the front and back cross members are completely rusted and need replacement costing $7,000. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2011 Mazda Mazda6. The contact stated that while her mother was driving at slow speeds in a parking area, there was an abnormally loud metallic sound coming from underneath the vehicle, and moments later, the vehicle became extremely difficult to maneuver. No warning lights were illuminated. The vehicle was towed to the dealer, who determined that the rear crossmember had detached from the vehicle due to excessive corrosion of the subframe. The contact was informed that the vehicle could not be repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 19V323000 (Structure, Suspension); the VIN was previously included, but was repaired in 2019. The contact stated that the recall repair was for the front passenger’s side lower control arm. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 150,000.

Alignment is off. Recall for my type of call for the control arm weakening and causing wheel alignment problems. Why isn't mine part of recall??