2009 MERCURY MILAN Complaints

The contact owns a 2009 Mercury Milan. The contact stated while driving at an undisclosed speed, the brake pedal was depressed and traveled to the floorboard. There was no warning light illuminated. The contact engaged the parking brake to stop the vehicle. The vehicle was restarted. The vehicle was taken to the dealer where it was diagnosed and determined that the ABS hydraulic control unit had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and confirmed that the VIN was not included in NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic). The approximate failure mileage was 100,000.

Check engine light airbag light brake light on my car they turned them off and they turned on right after

I RECEIVED A LETTER IN JULY OF 2021 ABOUT THE ABS CONTROL UNIT PROBLEM MY VEHICLE HAS. AT THE MOMENT THAT CONTROL MODULE IS NON-FUNCTIONAL. TO DATE FORD HAS NOT PRODUCED OR MADE AVAILABLE ANY OF THE PARTS NEEDED FOR THIS REPAIR AND WILL NOT EVEN ACKNOWLEDGE THE VEHICLE WHEN I CALLED THEM. I WOULD LIKE TO KNOW HOW LONG I HAVE TO DRIVE A VEHICLE WITH KNOWN DEFECTIVE BRAKES BEFORE FORD IS FORCED TO COMPLETE THIS REPAIR? THERE IS ALSO A BRAKE FLUID ISSUE WITH THIS VEHICLE THAT CANNOT BE ADDRESSED UNTIL THE NON-FUNCTIONING ABS MODULE IS REPAIRED. THE DEALER REFUSED TO CHANGE THE SAID CORROSIVE FLUID BECAUSE OF THE NON-FUNCTIONING ABS MODULE.

Brake pedal going to floor extending stopping distance. Early in 2022 I took it in for recall S1954. HCU passed test and dealer replaced DOT3 brake fluid with DOt4. 5/24/2022 Brake pedal started going to floor again. Dealer performed self test of hcu and electronic bleed hcu and said pedal was somewhat better but needed $400 of brake work to for Brake pads, lining and turn rotors. Car functioned fine for a few days. In early June I was driving on a wet street and put on the brakes. It appeared the ABS system was trying to kick in and suddenly the pedal again went to the floor. I was barely able to miss rear-ending a city bus. I pulled into a gas station, turned the car off. When I started it again the brake pedal went to the floor. After pumping it a number of times it came back up and was again functioning. Took it to dealer on 6/1/22. Dealer again tested the hcu test which once again it passed. They could find no other problems. Dealers recommended replacing the abs modlule and master cylinder to the tune of $1,400. Seems like they can test and find out which part isn't malfunctioning (hcu which is under recall), but cant test to find out which part is malfunctioning (ABS module or master cylinder) There is obviously still serious issue with the brake system on these cars that is not being corrected by the initial hcu recall. It needs to be fixed before someone is killed. There were no warning lights or messages relating to the brakes.

The problem I am having is with the cars braking system. I have extended brake travel required to stop the vehicle for which I have been issued two recalls. Because of the extended brake travel, I was unable to stop in time and had a front end collision with minor damage, which was not reported. The problem first showed up when I was forced to brake hard a few years causing the ABS to engage. The brake pedal traveled to the floor until the next time the ABS was engaged. Shortly after that, I was issued a recall stating the exact problem I was having. When I took it to my local dealership to get it fixed, they performed a test, changed the brake fluid, and said the system was working properly. It was not. Took it back to the dealership when hydraulic control valve became permanently locked open. They inspected it again and said the ABS unit needed to be replaced but the parts were not available. Contacted FMC customer service, and they were unable to help me either. I asked for a loaner vehicle, and received no response. Since then, I have been issued another recall and am still driving an unsafe car in a Michigan winter. All I want is a safe car to drive.

2009 MERCURY MILAN. CONSUMER STATED THAT AFTER HAVING SAFETY RECALL REPAIRED THEY ARE STILL EXPERIENCING ISSUES RELATED TO THE SAFETY RECALL.

Manufacturer Recall Number19S54 NHTSA Recall Number19V904 This recall has been on file since: Dec 18,2019. There is still no remedy. I believe this issue is causing my vehicle to have significant delays in braking into a complete stop. The manufacturer has failed or is unable to remedy this safety recall for my vehicle in a timely manner, so I would like to file a formal complaint.

After receiving the Safety Recall Notice 19S54 in the mail, I contacted my local Ford dealership and set up an appointment. On May 24, 2021, I brought my car to the dealership for this recall. At this time, I explained that the brake pedal was going to the floor intermittently. The car had 134,880 miles on it. The Hydraulic Control Unit was inspected and supposedly passed. So the dealer flushed the brake system and replaced the cap. After leaving the dealership, the car sat for several weeks. Two weeks after driving it again, I noticed that the brake pedal was going to the floor and it was difficult to stop the vehicle. I called the dealer and set up another appointment. The dealer had me wait about two weeks. On August 2nd, I brought my car back to the dealer for the same brake issue (Safety Recall 19S54). At this time the car had 135,492 miles. Again they inspected the brakes and the Hydraulic Control Unit. This time they found the HCU Assembly to be faulty and recommend that it be replaced. However, Ford Motor Company is refusing to cover this part under the Safety Recall 19S54 because they closed the recall after the May appointment. They want us to pay over $1500 to have it fixed.

The contact owns a 2009 Mercury Milan. The contact received recall notification for NHTSA campaign number 19V904000 (Service Brakes, Hydraulic) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was contacted and confirmed that the part was not yet available. The contact stated that the vehicle experienced the failure stated in the recall. The vehicle was not repaired. The manufacturer was contacted. The failure mileage was 98,000. Vin tool confirms parts not available.

The contact owns a 2009 Mercury Milan. The contact received notification of NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic). The contact stated that prior to the recall repair, the ABS warning light would appear intermittently. After the recall repair, the ABS warning light was illuminated continuously. The vehicle was taken to the dealer for the recall repair and the Hydraulic Control Unit (HCU) was tested as part of the recall repair, which it failed. The dealer informed the manufacturer of the failure however, the manufacturer declined the coverage for the HCU part replacement. The vehicle was not repaired and the dealer informed the contact that the vehicle was safe to drive with the ABS warning light illuminated. The failure mileage was 189,000.