GMC Complaints

The contact owns a 2021 GMC Yukon. The contact stated that the vehicle had a rough idle. There was an abnormal ticking and rattling sound detected. The vehicle lost oil pressure. The contact located smoke emerging from the vehicle. The engine light was illuminated. The vehicle was taken to the local dealer, where it was diagnosed with a failure with cylinder five, no compression, and bearing failure. The dealer suggested the engine be replaced. The vehicle was not repaired. The contact indicated that the failure was related to NHTSA Campaign Number: 25V274000 (Engine and Engine Cooling) but was not included in the recall. The manufacturer was contacted who referred to the NHTSA hotline. The failure mileage was unknown.

I was driving the vehicle on the highway the cruise control was on. All of a sudden I got a warning on vehicle info panel that stated vehicle power is reduced. The vehicle decelerated on its own and I could not accelerate past 55. The check engine light came on. I pulled off the road and turned the vehicle off. After about 10 minutes, I started the car back up and proceeded down the highway at normal speed. The check engine light remained on. I stopped at a Chevrolet dealer service center in Ft Stockton, TX, to have the vehicle looked at. They could find no error codes and could not duplicate the problem. I was sent on my way. This has happened multiple times while driving on roads in my area. Mostly while on the highway.

My thermostat failed in my car, my temp goes out and reads at 0° then my steering assist says it’s reduced. There are many forums online regarding this issue.

The transmission in my 2022 GMC Savana experiences severe harsh shifting during normal driving conditions. The issue is most noticeable between 1st–2nd gear and 2nd–3rd gear, with 2nd gear being especially problematic. The vehicle jerks and slams aggressively into gear during acceleration, causing unstable driving behavior and hesitation. In addition, when coming to a complete stop, the vehicle jerks forward unexpectedly. When accelerating again from a stop, the transmission jerks hard once more before shifting. This behavior occurs repeatedly during everyday driving and creates a safety concern, especially in traffic, intersections, parking areas, and while merging onto highways. The condition has progressively become worse over time and the vehicle currently has approximately 71,000 miles. The sudden shifting and jerking behavior affects vehicle control and creates concern for the safety of the driver, passengers, and surrounding traffic. No warning lights were present at the time of the issue. The problem appears to be related to the transmission/powertrain system. I also became aware that similar transmission and harsh shifting problems have been reported by other owners of the same make and model vehicle, despite my VIN currently not being included in any recall while others had a transmission recall

Telematic Modular Control is not working properly and part is on backorder. Dealership and GMC have refused to put into writing that my vehicle is safe to drive; however, they are refusing rental vehicle while awaiting arrival of part. Several of my safety features are not working correctly, my left turn signal went out randomly and my auto breaking has activated when there has been nothing near my vehicle.

2022 GMC Canyon AT4 Crew Cab. After the vehicle is shifted into Park and the engine is shut off, the ignition key cannot be removed from the cylinder. The key is physically locked, the steering wheel will not lock, and the vehicle cannot be reliably secured. The only workaround is to restart the engine and cycle the shifter repeatedly until the interlock releases the key. Recurring. Safety implications: operator cannot reliably power the vehicle off in an emergency, cannot lock the steering column, and may be forced to leave an unattended vehicle in accessory mode — fire, electrical, and theft risk. The defect is documented in GM's own literature. GM Bulletin PI1429 and GM TSB 19-NA-206 address this exact symptom on the Canyon/Colorado platform. NHTSA-archived GM TSB MC-10113734 (March 2015), "Ignition Key Cannot Be Removed and/or Does Not Rotate to the 'Off' Position," names the 2015 GMC Canyon and Chevrolet Colorado. The 2022 Canyon uses the same shifter and ignition-interlock architecture. Documented cause: failure of the transmission control lever microswitch that signals "Park" to the interlock solenoid. Documented fix: replace the shifter assembly. Reported to an authorized GMC dealer while still under the New Vehicle Limited Warranty. Dealer recorded the concern verbatim — "key stays locked in ignition when shifting to Park" — and closed it "unable to duplicate," no repair, despite the open bulletins. A second GMC dealer later refused to inspect, with the service advisor stating on the service drive that there is no fix, that they see this on Canyons and Colorados all the time, and that he had seen another such vehicle the day before. No diagnostic, no repair order. GM's Technical Assistance Center has since taken the position that the bulletins above do not apply to this vehicle, which is inconsistent with the bulletins themselves. No crash, no injury, no fire. Reporting a manufacturer-documented ignition-interlock defect GM is refusing to repair.

My vehicle torque converter repair on my 2020 GMC Yukon is shuddering. Why is this not a recall when there are various Yukons that are experiencing shuddering related to torque converter repair. This should be a recall. The problem has been confirmed by a GMC dealer. There were not warning lamps, no messages, or other symptoms.

I was driving, my front grill protector that was fixed with recall flew off again. This needs to be fixed. The part flew off hit my window and almost hit two cars that were behind me. This could of resulted in a bad accident. No warnings, it just happened.

My truck will not start when I press the push-button ignition. After waiting a few seconds and trying multiple times, it typically starts on the third attempt. Additionally, it will not restart after the auto stop feature activates at stop signs or traffic lights. This is very concerning, especially when pulling into oncoming traffic, as I’m worried the truck could shut off while I’m crossing. I have already had the battery, starter, and alternator checked, and all components tested fine. However, the issue is still occurring. There are also no warning lights or messages displayed on the dashboard.

While traveling on the highway in traffic, brakes became very stiff when depressed after attempting to slow down to exit. Was able to put full bodyweight into the brake pedal to slow enough to exit and navigate to the gas station right off the exit. Had to roll stop signs and unsafely navigate traffic because brakes were not working. Service Brake System warning light came on after the incident.