MAZDA Complaints

Our 2024 Mazda CX-90 has experienced the same significant malfunction on two separate occasions while being driven on busy public roads. The vehicle displayed an “Acceleration Limited Due to Battery Condition” warning and experienced significantly reduced/limited acceleration while driving. This put the occupants and other motorists at risk because the vehicle could not accelerate normally in traffic. A similar occurrence while merging, crossing an intersection, or traveling in heavy traffic could potentially result in a collision. The vehicle has been taken to an authorized Mazda dealership twice for the same issue and has been out of service for approximately six cumulative weeks. The vehicle is currently at the authorized Mazda dealership and is available for inspection. The dealership has been made aware of and is attempting to diagnose/repair the recurring condition. The exact component or system responsible for the failure is currently UNKNOWN. The issue recurred after the vehicle was previously returned to us following the first repair attempt. Prior to/during the failure, the vehicle displayed the warning message “Acceleration Limited Due to Battery Condition.” Any additional warning lamps, diagnostic codes, or underlying component failures are currently UNKNOWN and are being investigated by the Mazda dealership. Additionally, while our 2024 CX-90 was at the dealership, we were provided a separate 2026 Mazda CX-90 as a loaner vehicle. While that vehicle was being driven on a main public road, it suddenly lost all power. The steering wheel and pedals became locked or unresponsive, leaving the driver unable to normally control the vehicle while it was in traffic. Fortunately, a collision did not occur. The 2026 vehicle was returned to the Mazda dealership and is available for inspection. The exact cause of that failure is currently UNKNOWN. Experiencing safety-related failures while driving two separate Mazda CX-90 vehicles has raised serious concerns rega

The factory adhesive/anti-flutter sealant that bonds the outer hood skin to the inner structural frame has physically separated. There is a clear gap where the outer panel is no longer attached to the frame. As a result, the outer hood skin flexes and vibrates, especially at highway speeds. Impact / Safety Concern: The vibration and movement of the outer hood panel occurs directly in the driver’s forward line of sight. This creates a visible distraction while driving and can draw attention away from the road. Because the outer skin is no longer properly bonded to the structure, the condition is progressive and may worsen over time. Dealer Response: I documented the adhesive separation on the work order. The service advisor lowered the hood insulation and photographed the panel separation. Despite clear visual evidence, the technician closed the concern as “no issue with the hood insulation” and “no fault found.” The same separation was also observed on another CX-50 at the dealership. I am filing this report so the condition can be properly documented while the vehicle remains under warranty.

The drivers side inside door handle has quit working twice. The dealer has temporarily fixed it both times, but advised us to "just be more gentle with the handle". The cable is falling off of the door hinge inside the door, and the dealer claims they don't have a way to permanently fix it. They just put it back on its mount. We are afraid that the driver will not be able to escape the vehicle in an emergency. Both instances have been under 10,000 miles. The door handle works perfectly fine until it doesn't work at all. No warning given.

The automatic emergency braking in this vehicle is faulty. It misinterprets obstacles and uses the emergency braking inconsistently. I park in a parking garage and I have to slowly (less than 5 MPH) drive up any ramps because it apparently sees the ceiling of the garage as a obstacle and as a result, will randomly brake with no notice (which feels like getting rear ended). The dealer said it is working as designed and said I can turn this function off, but I have to turn it off every time I start the car. I also updated the sensitivity t the lowest setting, which didn’t help. I’m worried about this issue happening when I’m in traffic or bad weather and what might occur, like an accident. I’ve talked with other users of this same vehicle and they have ran into similar issues. Based on my experience, I think the system is defective and is a safety issue.

What is happening with my car are the exact symptoms of the known Mazda Recall 6824H - where the Smart Brake Support suddenly engages for no reason and when it does not need to - which has almost caused me to be rear-ended a few times. This has happened at least 7-8 times since I have owned the vehicle. Apparently, my VIN does not fall under the cars that Mazda reports for the Recall, but nonetheless, my car is still malfunctioning as the Recall describes, which is a safety issue for me. The Recall also states: "Due to an improper program setting, affected FSC (cameras) were not updated from production mode to normal mode. As a result, all three systems described (HBC, SBS, LAS) will not work as intended." My cameras are definitely not working as they should. I have had it in for service, and the technicians have not done anything at all. The Recall should definitely be expanded to owners experiencing these issues. As I have stated above, this incident has occurred at least 7-8 times, so I'll just enter in the most recent time that it happened in the Additional Details below since I cannot enter all of them. Thank you.

The contact owns a 2016 Mazda Mazda6. The contact stated that while driving at an undisclosed speed, a burning odor was noticed inside the vehicle. No warning lights illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed that the clutch disc kit had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure, and a case was filed. The failure mileage was approximately 125,166.

The steering seems to stick when turning left. Have give it a yank to get it back to normal

After vehicle has been parked for awhile, for example over night, there is a Popping sound or Clunking from front of vehicle after moving vehicle and applying brakes at first stop. Noise has been there since 2024. Popping, Clunking sound only when when vehicle parked again. There is also a loud Clunking sound sometimes, sounds like it is from the right front suspension, when driving on irregular, or bumpy road surface where i live. Sounds like something is not secured properly , tightened enough, or dampened enough. Like the Coil Spring flopping around in its holder. Have complained to the dealer numerous times. Was told that they could not duplicate the problem, even when vehicle was left there for about a week. Right front lower control arm was replaced on last visit, but noise is still there.

Have had 3 seats replaced under warranty by Graco and was told to make a report with you. The rigid latch anchors on two have been faulty after 2 months. The second one got stuck in the installed base and pulling the release button did nothing. The rigid latch on the first got stuck in the open position. The second they would move independently of each other and not lock in. The third is starting to have the same issue with getting stuck in the base. These have all happened within two months of normal use.

Uppababy markets their removable padding and fabric as washing machine friendly. Fabric was washed one time in the washer and the sharp Velcro stuck to the back of the fabric, ripping it. Brand new aria v2 car seat!