MAZDA Complaints

THE BRAKES DID NOT RESPOND TO TYPICAL PRESSURE REQUIRED TO STOP... WHEN I PUSHED HARDER ON THE BRAKE PEDAL IT FELT LIKE THE BRAKES WERE STARTING TO ENGAGE, HOWEVER I COULD NOT GET THEM TO FULLY ENGAGE AND STOP IN TIME TO AVOID REAR ENDING THE VEHICLE IN FRONT OF ME. I TOOK EVASIVE ACTION AND JUMPED THE CURB AND DIRECTED THE VEHICLE AT BANK OF NEWSPAPER STANDS IN ORDER TO COME TO A COMPLETE STOP.

THE TOP OF THE DASHBOARD IS MELTING. THE SHEEN IS CREATING A DANGEROUS REFLECTING GLARE OFF THE WINDSHIELD.

CAR HAS DIED THREE TWO TIMES AND IT IS LESS THAN A YEAR OLD. THERE ARE A LOT OF COMPLAINTS LIKE MINE ON THE INTERNET. PLEASE LOOK INTO THIS SAFETY ISSUE.

THE DRIVERS SEAT MADE A POPPING SOUND AND NOW ROCKS BACK AND FORTH LIKE A ROCKING CHAIR. I LOOKED UNDERNEATH THE SEAT AND DISCOVERED THAT A WELD ON THE LEFT SIDE OF THE SEAT IS BROKEN. I WENT ON LINE AND DISCOVERED DOZENS OF COMPLAINTS ABOUT THIS WELD BREAKING. IT EVEN APPEARS AS A PROBLEM ON A CAR REVIEW SITE. THIS IS A SAFETY ISSUE, AND EITHER A DESIGN FLAW OR POOR WORKMANSHIP. MAZDA SHOULD BE MADE TO FIX IT.

TL* THE CONTACT OWNS A 2003 MAZDA TRIBUTE. WHILE DRIVING AT APPROXIMATELY 55 MPH, THE BRAKES FAILED AND THE AIR BAG LIGHT ILLUMINATED. THE VEHICLE WAS MERGED OVER TO SIDE OF THE ROAD. THE CONTACT WAS AWARE THAT THE VEHICLE WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 07V157000 (SERVICE BRAKES, HYDRAULIC). THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 202,654.

2009 MAZDA 6. CONSUMER WRITES IN REGARDS TO TIRE SENSOR VALVE ISSUES. *SMD THE CONSUMER STATED THE LOW TIRE PRESSURE LIGHT ILLUMINATED FREQUENTLY. IT WAS DETERMINED, THE VALVE WAS CORRODED. THE VALVE WAS REPLACED WITH A CHEAPER ONE. WHILE DRIVING 65 MPH, THE CONSUMER EXPERIENCED A FLAT ON ANOTHER TIRE DUE TO CORROSION AND A CRACKED SENSOR VALVE. THE CONSUMER REPLACED ALL FOUR VALVES DUE TO CORROSION. *JB

I HAVE BEEN HAVING ISSUES WITH THE BRAKES MOSTLY WHEN RAINING OR SNOW. AT TIMES WHEN I GO TO HIT THE BRAKES THEY GET STUCK OR MAKE A GRINDING NOISE AND DON'T WANT TO STOP. THIS HAS HAPPENED NUMEROUS TIMES AND ALMOST CAUSED ME TO HIT ANOTHER CAR ON MULTIPLE OCCASIONS. I WILL TAKE IT IN SOON TO HAVE IT CHECKED NOW THAT I SEE THAT I AM NOT THE ONLY PERSON WITH THIS ISSUE. STARTING IN JAN 2015 I NOTICE A BURNING SMELL COMING FROM UNDER THE HOOD OF THE CAR. I HAD AN OIL CHANGE AND CHECKED FOR AN OIL LEAK TO FIND NOTHING WRONG WITH THE VEHICLE. AFTER RUNNING THE CAR FOR AT LEAST 20 MINUTES THE SMELL CONTINUES.

WHEN I ATTEMPTED TO REMOVE VALVE STEM COVER THE VALVE STEM CRACKED AND CAME APART. I HAD TO HAVE THE COMPLETE TPMS VALVE REPLACED. I THEN NOTICED THAT THE OTHER VALVE STEMS LOOKED IN THE SAME CONDITION. THE MAZDA DEALER SAID THAT THIS WAS JUST AGING AND THAT THE REST WERE O.K. I AM NOT SURE IF THEY ARE. I SAID THAT THE STEMS SHOULD NOT CRACK JUST BY REMOVING THE COVER.

DESIGN FLAW OF HEADLIGHT HAS CAUSED CONDENSATION TO FORM IN HEADLIGHT ASSEMBLY CAUSING XENON BULB TO SHORT CIRCUIT AND BLOW ON DRIVER'S SIDE HEADLIGHT.

TL*THE CONTACT OWNS A 2005 MAZDA MAZDA6. THE CONTACT STATED THAT WHILE ATTEMPTING TO REBUILD THE SUSPENSION WITH AFTER MARKET PARTS FOR THE LOWER CONTROL ARMS, THE CONTACT NOTICED THAT THE RETAINING NUTS INCLUDED WERE THE INCORRECT TYPES FOR THE CONTROL ARM. THE CONTACT MENTIONED THAT IF THE INCORRECT PARTS WERE TO BE INSTALLED IT WOULD CAUSE A CATASTROPHIC FAILURE. THE MANUFACTURER OF THE PART WAS NOT MADE AWARE OF THE FAILURE. THE VEHICLE MILEAGE WAS 200,600. .... UPDATED 06/30/15 *BF